Floating Slab – Construction, Advantages, & Disadvantages

 

Floating Slab – Construction, Advantages, & Disadvantages





What Is Floating Slab?

A floating slab is another type of concrete slab laid on the ground with no support. The slab is built in two stages. Footings are cast individually in the first stage, and then the center floor of the slab is poured.

Because of the floating slabs, the ground preparation is reduced to a larger extent. Since the floating slab does not have a connection with the foundation, it is also called a monolithic slab.

This type of slab is used when the structure requires low bearing capacity. This foundation is suitable for small structures where a deeper structure is not required and when additional infrastructure is not needed.

Floating slabs are used as the foundation for small structures such as manufacturing workshops, sheds, and garages. Let’s discuss its construction process.

Why Use Floating Slab?

Floating slab is one of the most economical foundation construction methods. Traditional foundations require a strip footing with a frost wall above. The strip footing installed below the frost level is usually 4 inches below grade. The cost of a strip footing and frost wall is higher because more excavation, concrete, and labor are required.

Construction Procedure Of Floating Slab

To begin the construction of floating slabs, the planned building requires a stable foundation to completely sustain the entire weight of the superstructure.

As previously said, they are more commonly utilized in garages, home additions, and sheds that do not require large foundations. Structure-wise, these structures are light.

When compared to conventional slab construction, floating slabs are proven to be the most suited and cost-effective. The steps involved in the construction of a floating slab are described below.

1. Site preparation

The first step is to inspect the site where the floating slab will be built. Clear the site of any trees, small shrubs, or other debris. Then, make an excavation plan, including where to dig and where to take the soil.

2. Excavation

After all the preparation, the next step is to excavate the site. Excavate the area for the slab in accordance with the level. In this step, make a drainage channel on the sides for water to drain out through the gravel base.

Water will be removed from the concrete slab foundation by sealing the trench with geotextile and gravel. Make sure to cover this channel with waterproofing material.

3. Laying Gravel Base

In this step, gravel is spread over the area to allow unwanted water to drain.

4. Reinforcement For Slab

After laying the gravel base, the next step is to prepare reinforcement as per the structural design. Lapping should not occur in a single location during reinforcement; instead, it should occur in a different manner.

In addition, the reinforcement must be in accordance with the slab’s dimensions and specifications in order to strengthen the structure.

5. Shuttering

Now, it is time to begin shuttering. The formwork may require a smooth surface, proper alignment, and good quality work. To prevent the formwork from opening during concrete pouring, the cover block should be fixed after shuttering.

6. Concreting

Concrete can be made on-site in a concrete mixer, or ready-mixed concrete can be used for floating slab concreting. All materials are mixed in a proper mixer machine to achieve high strength.

Adequate compaction should be performed during the concreting process. Depending on the area and workmanship, it is compacted by hand or by a mechanical vibrator. After 24 hours, the shuttering should be removed.

7. Curing

The slab should be cured for seven days after removing the shuttering. Curing plays an important role in achieving the desired concrete strength. For curing, water is sprayed.

Advantages Of Floating Slab

• A floating slab can keep moisture out of the floor. It is used to separate the ground and the superstructure. Additionally, it protects against water and frost.

• This slab has the spreading property, which allows vertical loads or stresses to be distributed over a larger area.

• A floating slab is a good option if your home requires an extension. This slab serves as a physical barrier between the superstructure and the ground. This prevents water and frosting. As a result, this slab is mostly used in cold-weather construction.

• Don’t require a wood flooring system & 8′-0″ basement wall.

• It requires less concrete and formwork for more economical and ecological construction.

• No footer trenches are required for this slab. They can be poured by trenching or excavating, which is a less expensive method. This slab causes no disturbance to the earth beneath it.

• Floating slabs can be heated with radiant floor heat, which provides a comfortable and balanced heat.

• Floating slabs are the best choice where the soil layer has a chance of shifting, primarily because of high moisture content.

• Cheaper house insurance because there is no basement to flood or chance of Radon gas infiltration.

Disadvantages Of Floating Slab

• It uses outdated technology.

• Less design resonance exists in foundations with floating slabs.

• Loss of storage space.

• Because there is no space in the floating slab for a sewage line, a trench must be dug during the construction.

• Floating slabs are ineffective for overloaded bearing structures.

• Repairing a floating slab is costly.

• Sometimes, the resale value of the house is lower because of the missing basement.

Uses

Floating slabs are mostly used for the following buildings

·                     Accessory buildings

·                     Garages 

·                     Drive sheds

·                     Houses & cottages

·                     Barns.

 

 

 

Comments

Post a Comment

Popular posts from this blog

NOTCHES AND WEIRs

Image
   NOTCH ,WEIR AND ITS TYPES Notch A  notch  may be defined as an obstruction over which the flow of liquid occurs   In case of measuring tank or reservoir, the opening is provided at the side of the tank such that the liquid surface in the tank is below the top edge of the opening. Weir A  weir  is a notch on a large scale used for measuring the flow of a river, canal etc. It is a concrete or masonry structure of substantial breadth built across the river in the direction of flow. This allows the excess water to flow over its entire length to the downstream side. Thus a weir is similar to a small dam constructed across the river, with a difference that the excess water flows downstream only through a small portion called  spillway  and in case of weir, the excess water flows over its entire length. Nappe and crest The sheet of water flowing through a notch or over a weir is known as  nappe  or  vein . The bott...
Read more

THE BASICS OF REBAR: A COMPREHENSIVE GUIDE FOR BEGINNERS

Image
 THE BASICS OF REBAR: A COMPREHENSIVE GUIDE FOR BEGINNERS The Basics of Rebar If you have ever wondered what gives strength and stability to the concrete structures that we see around us, the answer is (most commonly) rebar. Rebar, short for reinforcing bar, is the steel rods that are embedded in concrete that provide tensile strength to what is actually and prevent cracking. Rebar comes in different shapes and sizes, but the most common type is deformed steel rebar, which has ridges or indentations along its surface to create a better bond with the concrete. Deformed steel rebar has been used in the construction industry for over a century, and it has revolutionised the way we build. With rebar, and using elements such as beams,  beam ties , rebar mesh, and reinforced walls, we can create taller, stronger, and more durable structures that can withstand natural disasters, environmental changes, and human activities. Some of the most iconic buildings in the world, such as...
Read more

What are different diameters of steel used in construction field?

         In the construction industry, the appropriate selection of materials is crucial as they form            the fundamental basis for determining the strength and durability of structures. TMT (Thermo-Mechanically Treated) Steel is one of the essential components in construction as it stands out for its exceptional strength and ductility in building structures. Thus, contributing to the prolonged longevity and durability of the structures. In this article, we will delve into the different sizes of  TMT steel bars  and their different uses in the construction industry. These TMT Steel bars come in different sizes based on their varied diameters. The different diameter of steel bars are as follows: 8mm Steel Rod 10mm Steel Rod 12mm Steel Rod 16mm Steel Rod 20mm Steel Rod 25mm Steel Rod 32mm Steel Rod, etc TMT bars of varied sizes, play a pivotal role in diverse infrastructure initiatives, the versatility of TMT bars is ...
Read more